Chuck Curtis

I have begun the process of building my project. I had decided to build a bench seat for the project. I was going to initiall build the bench out of red oak (I had a bunch of it laying around) and cedar. I milled the lumber and wasn’t happy with the quality of the red oak, so went back to the lumber pile to pick out something different. However, since I had already milled the lumber, and the bench was going to be constructed with sliding dovetails (which I had never done before), I decided to build a prototype out of the red oak.

I just completed the prototype, and am glad I decided to build a prototype first. I wasn’t too happy with how the sliding dovetails turned out, and will change how I cut them for the final project. I also think I want to make the legs out of thicker stock (maybe 6/4 vice 4/4) and move the legs in a little from the edge so I can cut a bigger arc on the bottom of the stretcher ends. I also think that having wood that contrasts more will make the project look better. Right now I’m leaning on building the top out of white birch (again something I have laying around) and the legs and stretcher out of something darker (maybe Sapele). I would like to add some decoration to the top of the bench (the suspended surface) and am planning on routing an inlay into the top – a branch with leaves – out of darker wood.

The project isn’t too complicated, and having built a prototype should make the final build go quickly. Of course it will be tight to get finished by the end of the month, but that is still the plan.


I finished the build project. I wasn’t sure if I was going to make it (it has been a busy month). But I was able to do the final assembly and finish today… I may decide to do another coat of varnish on the top of the bench at a later date, but it is completed and added to the furniture in the house.

What were my challenges? I had initially thought of doing a bench out of red oak with an inlay. However the oak is turned out pretty plain (too mid-toned – I wanted a lighter shade of wood for the top). So I used the oak to make a prototype bench. What a great idea. It was a technical challenge – I had never constructed something like this before – and a design challenge – I didn’t really like the original design/proportions. Overall it was a great learning project, and even better to have a deadline to work to to force me to finish it, even if I had to work a little faster than I liked by the end.

After I constructed the prototype, I posted it for comments on Based on those comments (and my ideas), I decided to change the design of the bench:

– I would keep the legs with the same curve, but add a bigger diameter hole.
– I made the stretcher a lot smaller, more in proportion to the legs, and added a gentle curve to the stretcher.
– I made the top longer (32″ long) – It would fit the location better.
– I made the stretcher the same thickness as the stock from the legs, it seemed to be a better proportion.

The first step of the construction was to make the top, and inlay the leaves. I made the top of birch (I believe). I cut the leaves on the scroll saw and cut the inlays with the router (based on a podcast by Marc Spagnuolo). It turned out to be more challenging than it appeared by the podcast, but overall I like how the inlay turned out, and will probably incorporate that type of inlay into future projects.

I routed the sliding dovetail slot on the top. On the prototype I made a stopped dovetail, on this one I made a through dovetail and used a piece of scrap walnut as a filler for the front of the dovetail. I didn’t fill the back of the dovetail (so the bench can come apart, but not easily right now). I think if I had more time I may have added one for the back.

I then glued up the legs from sapele and milled the stretcher from the same. I believe it is sapele, but I have acquired a lot of lumber from a friend, and it wasn’t all labeled very well.

I cut the dovetail on the legs on the router table. I did cut the legs a little long, to ensure that if I cut too much off in making the dovetails, I could start over and not have to throw the legs away. After routing the dovetail on the legs, I cut the legs to length, and then drilled the hole and used the same template I used on the prototype to make the legs. I rough cut the curves on the bandsaw and used a pattern bit on the router to get the final shape.

I cut the curve on the stretcher and used a pattern bit to rout the curve to final shape.

The stretcher and legs are joined by a half-lap joint, and then the while leg/stretcher assembly is then attached to the top using a sliding dovetail. I used an American Woodworking project as inspiration for the construction method. I cut the slots for the legs/stretcher on the bandsaw and cleaned up by hand.

What did I do wrong? I made a couple of technical mistakes on the final project. The half-lap joints aren’t as clean as I would like them to be. I had the same problem on the prototype. I may have been rushing a little bit to get the project out the door on the final project. I also started to drill one of the cutouts at the end of the stretcher on the wrong side. It is on the back so isn’t very visible, but if I had more time, I would have cut a new stretcher and started over. I also finished the top prior to assembly, but didn’t have time to prefinish the rest of the pieces. I think it would have been easier to finish if I had prefinished all of the pieces.

What would I do differently the next time? Maybe use wood that would contrast even more (maybe ash for the top and walnut for the legs). I would prefinish all the pieces. I would try to get the half-lap joints tighter. I really liked the idea of building a full-sized prototype to help with construction and design ideas (I included a picture of the prototype to show the differences).

What were my costs? I purchased the red oak at $1/bdft, and the birch and sapele for about the same. Even if I had to pay market for the lumber, I didn’t use much lumber to create the project, maybe 8 bdft. Total cost for lumber I’ll say is $50. Plus $15 for a can of wiping varnish and $5 for glue and sandpaper for a total construction cost of $70.

The only tools I purchased for this was a new dovetail bit for the router (maybe $20).

3 Responses to Chuck Curtis

  1. Susanna says:

    Beautiful looking!
    /your girlfriend

  2. Waid says:

    Dude you use oak for prototype wood? Nice.

    • Chuck Curtis says:

      I picked up a bunch of red oak last year for less than $1/bdft. I was thinking of making the bench out of the red oak for the final project, but didn’t like the look of the lumber after it was milled. So I decided that since I already had the oak milled (and I could use a small bench on my back porch), I should finish the construction.

Leave a Reply to Chuck Curtis Cancel reply

Fill in your details below or click an icon to log in: Logo

You are commenting using your account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s